Clip-on ammeter digital clamp meter Current voltage resistance test clamp meter

DT - 360 features

1.2000 a backlit LCD display, clear reading

2. Low power tips and automatic shutdown function, power saving and durable

3. Simpale and data functions, convenient for reading

4. Can be manually and automatically switch range, intelligent measurement

5. NCV non-contact ac voltage indicator, to ensure safety

CEM DT - 360 automatic range ac clip-on table has a small body, moderate middle jaw, double injection sheath characteristics, to provide you with the most safe and comfortable hand feeling, convenient measurement, in narrow space can also be easily measured, closely large data with backlit LCD display is easy to read. Is your circuit, solder joint lines, electric power, overhaul and maintenance of good helper!

DT - 360 structure

1. The induced current clamps

2. The non-contact ac voltage indicator (NCV)

3. The tong head the trigger

4. Hold key data

5. LCD screen

6. MODE MODE selection button

7. com input jack

8. Function knob

9. Backlit buttons

A maximum 10. MAX hold key

11. The RANGE RANGE select key

12. V Ω))), and other input jack

Four, measure the diode and short circuit test buzzer

1. Insert the black pens and COM jack, socket inserted the red pens and)))

2. Select button to)))

3. Press the MODE button until the screen diode display symbols

4. The pens and contact with diode under test phase, is to the voltage of 0.4 V ~ 0.7 V, the reverse is displayed "OL". Will show the short circuit will display close to 0 mv, open "OL"

5. A short circuit test, resistance less than 150 Ω, produce the buzzer

Five, the non-contact ac voltage measurement (NCV)

Note: in order to prevent electric shock, before use, please ensure that the correct use of the non-contact ac voltage test pencil.

1. Let the clip-on table probe near or insert wire when output socket hole

2. If the wire with a 220 v alternating current output, indicator light will be lighted

Note: if the zero line and wire entwined, test to separate the two line at this time, to carry out the line of fire and the distinction between the zero line

Note: the design of non-contact ac voltage test pencil for highly sensitive detection. When faced with electrostatic or other band electrical body, may indicator light will light up or instantaneous flicker, which belongs to the normal phenomenon

A, alternating current measurements

Note: please ensure that before measuring ac current test pens and not connected to instrument

1. The transfer function of rotary table - 400 - a - 2 a

2. If not sure measuring gear beforehand, please first turn the wheel to high range and then gradually to a lower gear

3. Press the wrench open the clamps, put a piece of wire to be tested completely circle within the clamps LCD screen will be displayed on the current reading

Second, the dc/ac voltage measurement

1. Insert the black pens and COM jack, socket inserted the red pens and V

2. Select the button to V gear (distinguish between dc and ac)

3. Press MODE key to select ac or dc voltage

4. The tip of the pens and contact with the circuit under test

5. A reading on the LCD screen

Third, to measure the resistance

1. Insert the black pens and COM jacks, inserted the red pens and Ω jack

2. Select button to Ω gear measurement

3. Put the pens and contact with the circuit under test phase. Testing when it is best to disconnect at the end of the circuit board, so that the residual current not interfere with the measured resistance readings

4. Readings resistance displayed on the LCD screen

DT - 360 technical parameters

Alternating current measurements: 2 a, 20 a, 200 a, 400 a

Dc voltage measurements: 200 mv, 2 v, 20 v, 200 v, 600 v

Ac voltage measurements: 200 mv, 2 v, 20 v, 200 v, 600 v

Ω resistance measurement: 200 Ω, 2 k, 20 k Ω, 200 k Ω, 2 m Ω, 20 m Ω

Clamps opening size: about 1.2 "(30 mm)

: diode test: test current 0.3 mA typical values; The open circuit voltage: 1.5 V DC typical values

Short circuit buzzer test: less than 150 Ω buzzer. The test current is less than 0.5 mA

Sampling rate: 2 times per second

Input impedance: 10 m Ω (ac/dc voltage)

Display: 2000 with backlit LCD display

Battery: a 9 v battery

Automatic shutdown: about 15 minutes

Safety: safety standards CE meet ICE1010, 600 vcatiii

1. Please do not enter during testing beyond the allowed range of values

2. Please ensure that before measuring ac current test pens and not connected to instrument

3. Measure the voltage when not to gear to the current or resistance

4. Before the test will rotate to the corresponding measuring gear

5. When to change gear will usually pens and disconnect the circuit

6. After use, please put the table on the function selection switch to "OFF"

7. MODE button for ac/dc voltage, resistance, diode and switch short circuit buzzer test function

8. The RANGE key for automatic/manual switch RANGE

Can be widely used in electric power, communication, industrial engineering and other fields of circuit, solder joint lines, electricity, repair and maintenance.