Quantity(Piece/Pieces) | 1 ~ 1000 | >1000 |
Est. Time(days) | 7 | To be negotiated |
If you finish the payment today, your order will ship out within the delivery date.
5 Pcs Fuel Filter DAHL65 Assembly Universal for Boats and Ships Set of DAHL65-w30 Fuel Water Separator Diesel Engine
Type:1* assembly + 4* extra filter elements
Note:Support distribution and wholesale
Welcome Dropshipping to Cooperation
Item:DAHL65
Material: Paper
Part No.: DAHL65 DAHL65-W30 DAHL
Height: 13cm
Length: 17cm
Width: 11cm
Place of Origin: CN
Suit for car model :Boats and Ships Diesel generator engine Truck
Instruction Manual
Recommended Flow Rate:
(For Optimum Element Life & Separation Efficiency)
Model 65 & 75 Series.........................20 GPH (U.S.) (75.7 LPH)
Maximum Flow Rate:
Model 65 & 75 Series .......................30 GPH (U.S.) (113.5 LPH)
Flow Resistance:.....................................................0.75 In. Mercury
Maximum Working Pressure: ...............................25 PSI (172 kPa)
Temperature Range: ......................-50° to +225°F (-45° to +107°C)
Port Thread:
Single Units.............................................9/16-18 w/O-Ring Boss
Overall Height:
Model 65.......................................................6 3/8 In. (161.9 mm)
Model 75.......................................................6 1/8 In. (155.6 mm)
Width: ..............................................................4 3/16 In. (106.4 mm)
Depth: ................................................................4 3/4 In. (120.6 mm)
Dry Weight: ................................................................5 lbs. (2.27 kg)
Element Removal Clearance: ............................3 1/2 In. (88.9 mm)
Sump Capacity:...........................................................4 oz. (118 ml)
Seal Material:.........................................................................Buna N
Element Number:.........................................................66 (2 Micron)
...........................................................................66-W (10 Micron)
..........................................................................66-30 (30 Micron)
Element Material:................................Resin Impregnated Cellulose
A. FILTER MOUNTED ABOVE FUEL STORAGE TANK ___________________________
Installation procedures are the same as above plus an addition to
Step 3: A ball- or butterfly-type shut-off valve must be installed
ahead of the DAHL unit INLET. See Figure 2. This valve is
necessary to shut off fuel when changing the element. Valves are
available from your dealer or by contacting Baldwin Filters.
INSTALLATION
1. Select a location in the fuel line between the fuel tank and the
fuel pump, ahead of the vacuum side filters. All secondary or
pressure side filters located between the pump and the engine
should be serviced and left in place.
2. Mount the DAHL unit vertically on the vacuum (suction) side
of all fuel pumps in a convenient location for servicing and
inspection of contaminants in the bowl. Locate the height of
the unit between the bottom of the fuel tank and the inlet of the
fuel pump if possible. See Figure 1.
NOTE: Allow 3 1/2 inches vertical clearance below the unit for
servicing the element and draining the contaminants.
3. Install the fuel line from the fuel tank to the DAHL filter INLET
using appropriate non-galvanized fittings. See DAHL Fittings
Chart below.
4. Install the fuel line from the DAHL filter OUTLET to the
INLET of the transfer or fuel pump.
NOTE: To obtain maximum element life, remove as much
mechanical restriction as possible from the system by
doing the following:
a. Remove the primary filter (if this does not affect warranty).
b. Use the largest diameter fuel line that is practical.
c. Mount the unit as near to the level of the pump as possible.
d. Eliminate sharp bends in the fuel lines wherever possible.
The best indicator of a fuel element’s condition is a vacuum gauge. (See
85-V Series in Form 4005.) A tapped fitting is recommended for
mounting the gauge on the OUTLET port of the DAHL filter unit.
(Manifold units are already tapped and plugged.) Remove the 1/8 inch
plug and install the vacuum gauge there. Fittings and gauges are
available from your dealer or contact Baldwin Filters. Prime the filter as
indicated under ELEMENT REPLACEMENT section.
B. FILTER MOUNTED BELOW FUEL STORAGE TANK _
Nick Autoparts Factory Store
The company's main business: Fuel Filter,Oil filter, Diesel filter,
Air filter, Fuel water separator, Oil and gas separator, Shaped products,
Rig filter, PU filter, Filter assembly, Water cup, Filter aluminum seat,
Hydraulic filter, Gearbox filter, etc.
Welcome all major distributors at home and abroad to cooperate
In addition, the company Integrity agent to join, can be issued on a generation (direct to your customers), can also provide wholesale, price concessions, welcome to consult
You can send me the OEM number or photo of the accessory you need, and I can produce it for you in China.
Whatsapp: +8617685778975
Wechat: 17685778975
(1) all parts are under rigid quality control
(2) with high quality material
(3) competitive price: the larger quantity the lower price
(4) soon delivery: after your payment
(5) good service: your satisfied is our pleasure
$22.99~28.74
Min. Order:5