Product Parameters
This series of geomembrane welding machines meet the requirements of geomembrane welding of different thicknesses, and are suitable for PE,
HDPE, PVC, EVA, ECB, PP, PPR, drainage board, composite film, etc.
Welding of hot-melt materials
Mainly applicable to: anti-seepage construction in water conservancy, dyke slope protection, artificial lake, aquaculture, solid waste landfill, sewage treatment, petrochemical industry, tailings treatment, landscaping, planted roofs, etc.
Geomembrane welding machine TH-501
Input voltage: 220V
Frequency: 50Hz
Power: 800W/1 100W
Welding speed: 0.5-5m/min
Lap width: 10cm
Weld strength: ≥85% base material (tensile in shear direction)
Machine weight: 5kg
Insulation class: ||Class
Heating temperature: ordinary model 0-500°C/digital display model 0-600°C
Welding seam width: 16mm two lines / inspection seam 12mm
Welding material thickness: rubber wheel 0.2-1.5mm/steel wheel 1-2mm
Geomembrane welding machine TH-515
Input voltage: 220V
Frequency: 50Hz
Power: 800W/1100W
Welding speed: 0.5-5m/min
Lap width: 15cm
Weld strength: ≥85% base material (tensile in shear direction)
Machine weight: 5.3kg
Insulation class: |Class
Heating temperature: ordinary model 0-500°C/digital display model 0-600°C
Welding seam width: 16mm two lines / inspection seam 12mm
Welding material thickness: rubber wheel 0.2-1.5mm/ steel wheel 1-2mm
Geomembrane welding machine TH-520
Input voltage: 220V
Frequency: 50Hz
Power: 800W/1100W
Welding speed: 0.5-5m/min
Lap width: 20cm
Weld strength: ≥85% base material (tensile in shear direction)
Machine weight: 5.3kg
Insulation class: Class 11
Heating temperature: ordinary model 0-500°C/digital display model 0-600°C
Welding seam width: 16mm two lines / inspection seam 12mm
Welding material thickness: rubber wheel 0.2-1.5mm/ steel wheel 1 -2mm
Model: TH-501
Input voltage: 220V
Frequency: 50Hz
Power: 800W/1100W
Welding speed: 0.5-5m/min
Lap width: 10cm
Weld strength: ≥85% base material (tensile in shear direction)
Machine weight: 5kg
Insulation class: | |Class
Heating temperature: Ordinary model 0-500℃/Digital display model 0-600℃
Weld seam width: 16mm two strips/detection seam 12mm
Welding material thickness: rubber wheel: 0.2-1.5mm/ steel wheel: 1-2mm
Model: TH-515
Input voltage: 220V
Frequency: 50Hz
Power: 800W/1100W
Welding speed: 0.5-5m/min
Lap width: 15cm
Weld strength: ≥85% base material (tensile in shear direction)
Machine weight: 5.3kg
Insulation class: | |Class
Heating temperature: Ordinary model 0-500℃/Digital display model 0-600℃
Weld seam width: 16mm two strips/detection seam 12mm
Welding material thickness: rubber wheel: 0.2-1.5mm/ steel wheel: 1-2mm
Model:TH-520
Input voltage: 220V
Frequency: 50Hz
Power: 800W/1100W
Welding speed: 0.5-5m/min
Lap width: 20cm
Weld strength: ≥85% base material (tensile in shear direction)
Machine weight: 5.3kg
Insulation class:| |Class
Heating temperature: ordinary model 0-500℃/digital display model 0-600℃
Weld seam width: 16mm two strips/detection seam 12mm
Welding material thickness: rubber wheel: 0.2-1.5mm/ steel wheel: 1-2mm
Product operation process:
1. The joystick is leveled to separate the upper and lower pressure wheels to prevent the idler damage to the machine after starting.
2. Turn on the power and turn on the power switch.
3. Set the temperature first, normal materials above 1mm, the temperature is adjusted to about 350 degrees, the control box
When the upper indicator is red, it is in the heating state.
4. Adjust the welding speed according to the material thickness, according to the normal 1mm material, the speed is adjusted to 2.5m
about.
5. When the red light of the control box turns to green light, put the materials from the left and right sides of the machine, and the joystick will play from bottom to top, 90 degrees to the ground, and the machine will start to walk.
6.Adjust the speed according to the welding effect, the temperature is high and the speed is fast, otherwise, the temperature is low and the speed is slow (try to
Do not adjust the temperature in the middle, set the temperature first when starting the machine, the material is thin or the first operation, set the temperature lower when starting the machine. )
7. After welding is completed, level the joystick at the first time to separate the upper and lower pressure wheels (to prevent high
Warm the pressure roller), and then adjust the temperature to the minimum, and finally shut down and unplug the power.
